Hello friends!! In this article we are going to discuss on Iptables and its uses. Iptables is a command-line firewall, installed by default on all official Ubuntu distributions. Using Iptables, you can label a set of rules, that will be go after by the Linux kernel to verify all incoming and outgoing network traffic.
Today we will look at some basic concept of Ipatble using various Iptables options to generate a Filter Table which will filter the incoming and outgoing traffic
Basic Iptables Options
-A : Add this rule to a rule chain.
-L: List the current filter rules.
-m conntrack : Allow filter rules to match based on connection state. Permits the use of the –ctstate option.
–ctstate: Define the list of states for the rule to match on. Valid states are:
- NEW – The connection has not yet been seen.
- RELATED – The connection is new, but is related to another connection already permitted.
- ESTABLISHED – The connection is already established.
- INVALID – The traffic couldn’t be identified for some reason.
-m limit: Require the rule to match only a limited number of times. Allows the use of the –limit option.
Useful for limiting logging rules:
- –limit – The maximum matching rate, given as a number followed by “/second”, “/minute”, “/hour”, or “/day” depending on how often you want the rule to match. If this option is not used and -m limit is used, the default is “3/hour”.
-p: Describe the connection protocol used.
–dport : The destination port(s) required for this rule. A single port may be given, or a range may be given as start: end, which will match all ports from start to end, inclusive.
-j : Jump to the specified target. By default, iptables allows four targets:
- ACCEPT – Accept the packet and stop processing rules in this chain.
- REJECT– Reject the packet and notify the sender that we did so, and stop processing rules in this chain.
- DROP– Silently ignore the packet, and stop processing rules in this chain.
- LOG– Log
-I: Inserts a rule. Takes two options, the chain to insert the rule into, and the rule number it should be.
-I: INPUT 5 would insert the rule into the INPUT chain and make it the 5th rule in the list.
-s: –source – address [/mask] source specification
-d: –destination – address[/mask] destination specification
Iptables follow Ipchain rules which is nothing but the bunch of firewall rules to control incoming and outgoing traffic
Three Important Types Iptable chains
Input Chain: Input chain rule rule is used to manage the activities of incoming traffic towards server.
Output Chain: Ouput chain rule is used to manage the activities of outgoing traffic from your server.
Forward Chain: A forward chain rule is used for adding up rules related to forwarding of an ip packet. This is usually used while you have a Linux machine as router linking two networks collectively.
As discribed above by default install iptable is availabe in all Ubuntu distribution but if it is not installed in any Linux based system and you want to install it then excute given below command.
sudo apt-get install iptables
By default iptable is blank which allows all incoming and outgoing connection traffic without filtering them. In order to verify inbuilt rules of iptable we need to execute following command which displays the list of rules if added in iptables.
sudo iptables -L -v
here -L is used for display the chain rules of iptables and -v for complete information.
Allow Incoming Traffic
In order to allow traffic for any particular port you can use given below command here we have accept incoming on port 22 for SSH, 80 for HTTP and 443for HTTPS respectively
sudo iptables -A INPUT -p tcp –dport 22 -j ACCEPT
sudo iptables -A INPUT -p tcp –dport 80 -j ACCEPT
sudo iptables -A INPUT -p tcp –dport 443 -j ACCEPT
So it will allow tcp connection when traffic will coming on port 22, 80 and 443.
Drop/Deny Incoming Traffic
In order to deny traffic for any particular port you can use given below command here we have drop incoming on port 21 for FTP and 23 for Telnet respectively
sudo iptables -A INPUT -p tcp –dport 21 -j DROP
sudo iptables -A INPUT -p tcp –dport 23 -j DROP
So it will deny tcp connection when traffic will coming on port 21, 23 and give a message Time Out.
Reject Incoming Traffic
Reject and Drop action closely work same in order to obstruct the incoming traffic from establishing connection with server only the difference is that, here it will send message with “ICMP message Port Unreachable” and drop the incoming packet. You can use given below command here we have reject incoming on port 25 for SMTP.
sudo iptables -A INPUT -p tcp –dport 25 –j REJECT
So it will drop tcp connection when traffic will coming on port 25 and give a message Destination Port unreachable.
Allow Incoming Traffic from Specific IP
In order to allow traffic form only a particular IP to establish a secure connection between server and client you can execute given below command
sudo iptables -A INPUT -s 192.168.1.104 -j ACCEPT
It will accept packet coming from network 192.168.1.104
Block Specific Network IP
In order to deny traffic form only a particular IP to establish a secure your server from attacker’s IP you can execute given below command
sudo iptables -A INPUT -s 192.168.1.102 -j DROP
It will deny packet coming from network 192.168.1.102
Block Specific Network Interface
To block a specific network interface, for example eth0, execute given below command which drop the incoming traffic coming from 10.10.10.10
sudo iptables -A INPUT -i eth0 -s 10.10.10.10-j DROP
Here you can change the action to allow traffic from a particular network interface using –j ACCEPT options.
Block Specific IP Range
To block a specific IP range in order to deny, the incoming traffic coming from specific range of IP. Execute given below command which drop incoming packet coming from IP 192.168.1.100 till IP 192.168.1.200
sudo iptables -A INPUT -m iprange –src-range 192.168.1.100-192.168.1.200 -j DROP
Here you can change the action to allow traffic from a particular IP range using –j ACCEPT options.
Block Specific Mac Address
To block a specific Mac address in order to deny, the incoming traffic coming from specific machine. Execute given below command which drop incoming packet coming from given Mac address or attacker machine.
sudo iptables -A INPUT -m mac –mac-source FC:AA:14:6A:9A:A2 -j DROP
Here you can change the action to allow traffic from a particular Mac address using –j ACCEPT options.
Block Ping Request
Network administrator always concern with network security therefore they always Block Ping request either by using Drop or Reject action , here we are blocking Ping request using DROP option as given in below command.
sudo iptables -A INPUT -p icmp -i eth0 -j DROP
View List of Applied Chain rules
In order to view our applied chain rules once again we are going to execute given below command which will dump list of Iptable rules.
sudo iptables -L
From given below image you can observe 4 columns which contains records of IPtable rules.
Here these columns define following information:
Target: Defines applied action
Prot: stand for Protocol type that can TCP, ICMP or UDP
Option: further option to define rule, here it is blank
Source: Incoming traffic network IP Address
Destination: Host IP address which will receive incoming traffic packet.